21.x Firmware

21.01 - 03.08.2021

IMPORTANT INFORMATION:

Firmware 20.05.03 needs to be installed, before installing the 21.01 Firmware

Reloading the browser cache can be required. Use CRTL+SHIFT+R or CTRL+F5 or SHIFT+F5 to reload it

• fixed issue with DTMF passthrough on SIP->SIP calls

• fixed SDP handling issue, when there were multiple 180 RINGING messages with and without SDP

• fixed some issues on firmware downgrade

• fixed some issues on firmware upgrade

• fixed issue on incoming LTE call, when one call is already connected

• fixed error in API function TelephonyGetCdr and added new parameter download_old

• fixed some issues in the Fulltrace

• fixed handling of TON in Calldeflect/Rerouting facility for generating 302 redirect

• fixed rejecting calldeflect/rerouting with returnError Facility when calldeflect is disabled

• fixed LTE state table and added more information about technology

• added GUI support for TLS 1.2

• added SIP support for TLS 1.0, TLS 1.1 TLS 1.2, removed support for SSLv3

• added TLS certificate verification now enabled by default (if there is a problem registering to your TLS SIP server, upload the correct certificate or disable verification)

• added new licensing mechanism for SIP-SIP calls (transcoding and transparent channels)

• added made RTP handling selectable (transparent vs transcoding calls)

• added more performant handling of transparent SIP->SIP RTP streams

• added access to isgw telnet konsole in the GUI

• added custom tones to be configurable in the GUI for FXO

• added wait4idle timeout configurable on FXO to handle incoming ringing

• added verify_ringing option to FXO port group

• added FXS ring oscillator intervals to be configurable

• added experimental option ltedtmf, to handle non inband DTMF indications on LTE calls

• added config option anonymous_from_user_on_privacy

• added activationDiversionQ numbers are now available as dialplan variable

• added showing the network link status in GUI

• added interface can now be given for ACL rules

• added reworked DoS protection settings, can now be configured for different packet types and interfaces

• added more information to call statistic (formerly port statistic)

• reworked the Network Settings page

• improved debugging of PSTN ports in fulltrace

• performance improvements in GUI

• reduced memory consumption of isgw

• using ephemeral portrange 50000-60000 for outgoing UDP requests

• after a hardware factory reset via jumper, the SSH, HTTP and HTTPS Ports will be opened

20.x Firmware

20.05.03 - 17.05.2021

• bearer capability will now be passed through transparently on ISDN->ISDN calls
• added config option bearer
• fixed problem on ISDN->ISDN calls when CLEARMODE codec was used
• fixed control of LED lights on 24 FXS gateway
• changed format of analog port voltage logging
• fixed problem sending Invites to different proxy after registrar failure
• fixed XSS issue

20.05.02 - 09.04.2021

• fix for sdpless re-invite
• fix for incoming sdpless invite
• fix for authenticating incoming bye message
• fixed passing through SIP INFO for SIP-ISDN
• fixed Language issue on State page
• fix for audio problems for new LTE module
• fixed sending syslog messages after restart
• fixed generating some config files after hardware factory reset
• fixed problem with DNS SRV when DNS server was not available on startup
• added using SRV alternative peers, when register attempt fails
• reordered items on GUI logging page
  
• fixed sporadically ocurring problem with PSTN database setup after a factory reset
• added ACL rule to allow access from bfdetect tool

20.05.01 - 17.12.2020

• fixed typo in german translation, rendering the GUI inaccessible

20.05 - 16.12.2020

IMPORTANT INFO: Switching to german language renders the GUI inaccessible

In this case, install the 20.05.01 Firmware by rebooting into update mode by calling:

http://GATEWAYIP/app/api/api.php?apiCommand=FirmwareUpdateReboot

replace the string GATEWAYIP with the IP of your gateway

• changed if ISDN port is blocked, calls are rejected with cause 44 now
• added allowing schedule of graceful activate/reboot when no calls are affected
• added support for callgroups
• added option max_simultaneous call for SIP groups
• added improved network troubleshooting
• added support for SNMPv3 UDP/TLS
• added config option t38_ignore_offer
• added contact_all_setting allowing to modify registration contact header
• added monitored_sip_peer option to allow shutting down ISDN ports when SIP peer goes down
• added improved time settings configuration, Summer/Wintertime change now configurable
• fixed issues in time settings management
• fixed issues during factory reset
• fixed showing used ISDN channel in CDR when call was rejected directly after SETUP
• fixed backup/restore of hostname
• fixed not accepting bye from caller in early dialog on SIP to SIP calls
• fixed issues with GSM table not loading
• fixed not setting contact in validating OPTIONS packets, when validating without registration
• fixed dnssrv request for peers configured with TLS
• fixed GSM/LTE unicode converter
• fixed restoring NTP host from backup
• fixed not using configured dtmflen value, when rfc2833_passthrough=0
• fixed memory leak when using validate without registration
• fixed handling of an re-invite not containing SDP
• fixed sending out rfc2833 events when dtmfmode=inband was used
• fixed not refreshing DHCP anymore when request failed
• fixed problem adding some network routes
• fixed issue correctly deleting and deregistering cloud settings on factory reset
• fixed number prefixing when failover_account is used, using settings from failover account
• fixed crash when restarting ISDN port that was not configured
• several GUI fixes and improvements
• GUI allowing multiple selection and deletion of SIP groups
• GUI fixed dialplan javascript delete issue
• GUI added from_display and other variables to list of selectable SIP settings
• GUI added cancel button to Full-Trace
• GUI added additional options for managing Full-Trace
• GUI added ajax refresh for active calls
• disabled PRACK support by default, if not explicitly enabled via experimental option enable_prack
• disabled support for SNMP traps

20.04.01 - 13.08.2020

• fixed problem resetting the GUI password

20.04 - 07.08.2020

• fixed unnecessary restarting of voice channel on SIP->SIP calls in case of reinvite
• fixed memory leaks occuring on gateways with T1E1 modules
• fixed offering wrong RTP port, when dialplan was searched multiple times on analog overlap dialing calls
• fixed addressing deprecated/wrong target IP on outgoing INVITEs when DNS SRV was used and DNS address changed occurred
• fixed SMS not being able to contain € sign
• added SMS Webhook, allowing URL to be contacted on SMS reception
• added Network troubleshooting features to GUI
• added config option header_passthrough_filter to be used together with config option header_passthrough
• added GUI option to disable the cloud redirect function
• added informative message about cloud status
• restart_after_linkloss sends additional restart message on channel 0
• closing dialplan_debug window on session timeout
• different loglevel settings are now individually configurable in the GUI
• supporting now new beroNet LTE module
• cloud monitoring and status will be enabled when registering to the cloud
• optimized Yellow Activate (ACL rules restarted only after have been updated)
• homogenized physical and GUI LEDs for LTE module
• fixed issue updating DNS Server
• fixed GUI issues (Call-Progress Table, Wizard, Market)
• fixed 3CX Wizard redirect issue
• on GSM and LTE cards SMS stored on the SIM will be deleted during initialization (please backup any important messages)

20.03 - 05.06.2020

• fixed some stability issues
• fixed some memory leaks
• fixed some hang issuesimproved GUI performance
• fixed GUI bug saving SIP peer secret
• reworked DNS system, using internal DNS cache for better performance
• fixed some display problems during dialplan debug
• added support for "Technische Richtlinien Notruf" of the Telekom
• fixed problem with ISDN calldeflect when using very long numbers
• fixed some Labelling errors in the GUI
• added new Wizard for 3cx and other VoiP PBX
• added Api Functions CFActivate and CFDeactivate
• added support for LE910C1 LTE
• beroCloud Configuration now has own menu entry
• showing beroCloud registration status on demand
• added support for SMS delivery reports, added Api function SmsGetSendReport
• incoming SMS only deleted automatically if there are more than 1000 unfetched
• added experimental option telnet_max_connections, default value is 4
• increased allowed syslog port range
• fixed issue with SDP-less re-invite in connected SIP->SIP call
• fixed wrongfully setting SDP on SIP->SIP call in some situations
• fixed losing part of SIP configuration when Factory Reset is done and 'keep SIP settings' is selected
• added preparations for beroCloud redirection service

20.02 - 19.02.2020

GUI-Mode: Reloading the browser cache can be required. Use CRTL+SHIFT+R or CTRL+F5 or SHIFT+F5 to reload it

• fixed problem on SIP→ISDN BRI/NT  calls not going to next free port if all channels are occupied
• added keeping 'ACL settings' during Wizard Configuration
• added a PHP validator during a GET or a POST request 
• improved the Javascript validator
• improved the security against XSS and SQL injection vulnerabilities
• fixed problem restarting LTE port on State page
• fixed problem saving 'Remote Management' Settings in German-Mode
• fixed some Javascript errors or not expected behavior
• fixed GUI-error with 'Dialtone passthrough' settings from FXO module
• fixed GUI-bug from Dialplan popup settings (Easy and Advanced Mode)

20.01 - 06.02.2020

• fixed prepending of VAZ (prefixes) when no national/international prefixes have been set
• fixed updating and reload problems of causes map
• fixed erroneous reregister request to the berocloud, after deregistering, improved GUI presentation
• fixed missing values in SIP settings dropdowns (e.g. in From user/Pai User ...)
• fixed displaying incorrect value in the GUI for Destination/Source Number format
• fixed not capturing localhost SIP message during fulltrace
• fixed early audio on PSTN->PSTN calls
• fixed instability when SIP INFO package without payload was received
• fixed problem with downgrade from 19.xx to 16.xx not starting, occurring on very old gateways
• fixed losing of transport settings for the SIP stack when upgrading from 16.xx to 20.xx
• fixed showing of SMS Tab in the GUI for LTE modules
• fixed problem on LAN/WAN using same MAC addresses, using different MACs now
• some minor GUI layout improvements
• added new value auto for SIP dialplan source and dialplan destination and made it default
• added new config option sdp_codec_selection, passing through the offered codecs
• using second DNS server if the first on fails
• GUI session timer is refreshed on click activity
• on BRI rejecting now SETUP, when two calls are already
• improved Dialplan Debugging

19.x Firmware

19.07 - 11.12.2019

• some GUI modifications (some pages are now organized in tabs, showing additional information)
• added GSM/LTE provider selection
• improved presentation of GSM/LTE status
  
• added validation as option to SIP peers without registration
• fixed issue when configuring
• fixed issue with 2FXO-1FXS module combination
• improved behaviour of the LEDs of the PSTN RJ45 ports
• fixed application of early_audio settings on SIP->FXO calls
• added option for permanent remote support
• fixed encoding REDIR_NR in ISDN NT-stack
• fixed short hangs triggered by non-responding DNS server
• default values changed: sip_from_display_setting=none (from display empty)
• default values changed: sip_ppi_user_setting=none (PPI header not added)
• default values changed: codecs=pcma (only pcma is now offered by default)
• default values changed: t38=0 (no t38 on PSTN/SIP calls)
• default values changed: s2s_t38_passthrough=0 (no t38 on SIP2SIP calls)
• default values changed: cd=1 (call deflect is enabled by defaull)
• default values changed: i2s_destination_numformat (default now: +(int)(nat)num, old default unknown: (num))
• default values changed: i2s_source_numformat (default now: +(int)(nat)num, old default unknown: (num))
• default values changed: TCP and UDP are by default activated now on each SIP stack
• NTP server pool.ntp.org configured by default
• no default ACL rules anymore, only access from local network is initially configured
• fixed bug losing the causes map on firmware update
• fixed bug re-registering SIP peers on DNS server timeout
• fixed bug on SIP->FXO calls, when FXO->SIP call was already active on analog port
• added support of ie_on_sip X-BF_FACILITY_MLPP header
• fixed generation of pcap traces when VLAN was activated
• fixed issues with PCM bridging
• SIP CLEARMODE calls automatically now offer UNRESTRICTED_DIGITAL as bearer capability on ISDN, and vice versa by default
• added clearmode_auto option, allowing to configure the CLEARMODE/UNRESTRICTED_DIGITAL bearer configuration
• fixed issue when re-invite SDP target url and gateway IP are identical
  

19.06 - 18.10.2019

• fixed problem of displaying T1E1 modules in the GUI
• fixed small memory leak

19.05 - 02.10.2019

• fixed issue using wrong cidlen and crlen on PRI

19.04 - 30.09.2019

• added codec selection for LTE
• added config option gsm_clir to configure
• added configurability of ISDN cidlen and crlen for BRI
• fixed issue uploading/deleting SIP TLS certificates
• fixed incorrect prepending of country and city code
• fixed collecting of debug data during full-trace
• fixed slow down of the GUI while checking for firmware
• cloud based remote session can be now ended via the GUI
• better handling of privacy header in auto mode on SIP->SIP calls (outgoing leg uses values of first leg)

19.03 - 28.08.2019

• fixed issue with incomplete configuration after update from 16.xx firmware
• fixed log rotating pcap files during full trace
• fixed problem of setting nameserver when DHCP is on
• fixed issue on SIP->ISDN calls when externip of stun server was used
• fixed netconfigserver reported ip when bonding mode is selected
• added configurability of NTP server when DHCP is activated, explicitly given NTP server has preference

19.02 - 06.08.2019

• fixed missing files in Full Trace (gsm debug.log on LTE, LAN pcap in bonding mode)
• added missing Termination Causes to CDR
• Reworked and improved the different Gateway Wizards
• fixed erroneous prepending of configured prefix to automatic number format
• added GUI field for configuring SIP contact header
• fixed problem with FXS not working
• fixed file descriptor leaks
• removed s2s_302_passthrough
• added call_forwarding_mode instead, allowing to either send a 302 or a reinvite (with optional diversion header)
• config values from_sip_dest_setting (dialplan destination) and from_sip_src_setting (dialplan source) can be now defined with a regular expression
• added config values sip_priv*, to add custom headers to an outgoing Invite

19.01 - 27.06.2019

Most notable changes in comparison to current 16.15 firmware:

• Support for beroNet 3LI gateways with two ethernet ports
• Separate SIP stacks can be configured for each network interface
• Sip peers can be individually configured to use their own bind port
• Facilities for DoS Protection

16.x Firmware

16.17 - 19.11.2019

• fixed slowness issue in GUI

• fixed initialization issue with FXO and FXS after hardware factory reset was done

16.16 - 24.09.2019

• better handling of privacy header in auto mode on SIP->SIP calls (outgoing leg uses values of first leg)

• added config option isdn_no_sending_complete
• fixed incorrect prepending of country and city code
• fixed sending two SETUPs on SIP->ISDN calls, when stun or externip was enabled
• fixed problem with setting iptables rules for SIP peers with long group name
• fixed printing of configuration settings

16.15 - 19.06.2019

• fixed error in SDP when rejecting T.38, if multiple media sections were offered

• fixed problem on SIP->FXO calls accidentally terminating FXO->SIP call on used port
• fixed potential resource leak of RTP ports on SIP->SIP calls
• for SIP->SIP calls, dtmfmode can be configured for both SIP legs individually
• new options for s2s_nat_opener
• better handling of potentially broken https certificates

16.13 - 29.03.2019

• fixed error when restoring isgw.causes

• fixed XSS vulnerability

• fixed prefixing dad with ton prefix

• fixed problem with no audio on SIP->SIP calls when send_only was offered in SDP

• fixed problem for with SDP offers offering codecs with higher sampling rate

• fixed offering of tracing ISDN ports in fulltrace only when no ISDN ports are available

• fixed issue with analog port configuration during firmware update

• added config option config option isdn2sip_source_numformat

• added support for FXO adminstrative offhook mode

• added new parameters to use_privacy_header config option, options are now auto, off, none and id

• added config option sip_302_contact_user
• added config option sip_302_contact_url
• removed config_option s2i_transfer_url_cd

• removed config option d2s_oad_prefix_setting

• removed SIP profile management from GUI

• config option disable_prack now used for inbound sip calls too

• on T1/E1 modules E1-HDLC is used as default, for reconfiguring to CAS/T1 update the hardware configuration during a factory reset now

• now displaying hardware configuration table when the module has been be just plugged

• now display pipe installation-progress when a new tab is opened

• improved collecting of debug data during full-trace

• improved handling of FSK caller-id detection on FXO ports

• a couple of cosmetic improvements in the GUI

16.12 - 11.01.2019

• fixed disabling of echo canceller

• fixed VAZ prepending in case of usage of failover proxy

• fixed VAZ prepending in GSM and FXS calls

• fixed timeslot allocation for T1E1 module

• fixed problem with s2s licence reading for new cards starting with serial number 30

• added config option ec_sparse_params

• added config option s2s_rtp_passthrough

• added config option r2config for setting MFCR2 parameters

• added codes for rejecting RTP or T.38, status code can be configured now in the causes map

• changed default reject status code from 415 to 488 for T.38

• changed default for sip_info_on_facility to 0

16.11 - 16.08.2018

• fixed bug affecting incoming invites unintentionally being rejected sometimes
• fixed rtp_packet_size config option for SIP→SIP calls
• fixed SIP→SIP license parsing on new 3-line-interface gateway

16.10 - 05.07.2018

• fixed setting correct cause from causes.map in ISDN DISCONNECT and RELEASE_COMPLETE, if no dialplan entry was found
• fixed wrong setting of contact string, when externip/stun  was not used
• fixed a memory leak when using DNS SRV
• fixed error when registering to the cloud
• fixed password problem between Zeroconf and PBX Wizard
• fixed error in SIP→SIP dialplan entry when using dialplan variables
• fixed bug with timeshift of timezone with half hours
• contact header SIP URL port will always be formatted including port, even if it is 5060
• fulltrace starting now rotates the logfiles
• added config option s2s_t38_passthrough

16.09 - 23.04.2018

• changed maximum SIP registration refresh value from 2000 to 3600
• fixed error configuring PCM slave mode
• fixed behaviour when T.38 reinvite was rejected and a G711 re-invite was received
• fixed setting correct port when sip domain is used
• using uppercase for codecs in SDP now
• isdn2sip_destination_numformat now used for fxs call as well
• added config option sip_info_on_facility
• added config option s2s_nat_opener
• handling 302 correctly on SIP→SIP calls
• waiting longer time to go into idle state on FXO calls
• added experimental_option emergency_numbers
• fixed stability issues
• experimental option no100fix can be now 0, 1 or 2
• now sending 302 transfer in SIP direction if calldeflect is received on ISDN side and cd=1
• fixed no audio problem when SDP was contained in 182 message
• refreshing registrations when DNS query result has changed

16.08 - 07.11.2017

• added toneset for Ireland
  
• fixed hostname setting
• fixed userapp-version issue
  
• fixed not printing first line in dialplan debug
  
• fixed call progress table backup&restore bug
• changed default setting of ppi/rpi/xheaders, they are now disabled by default, sip_pai_user=${new_source} now
  
• hostname/gateway not displayed in dhcp mode
• ntpserver setting overrides DHCP provided ntp server if set

16.07 - 25.07.2017

• fix for parsing sip ppi header
  
• added option no100fix, fixing problem when no 100 trying is received
• fixed sip failover behaviour on gsm
• fixed memory leak when using stun
• fixed problem encoding ISDN connected party number

16.06 - 28.06.2017

• fixed security issues with telnet access to card
• fixed SIP problems with peers not listening on standard SIP port
• fixed GUI error message after language switch
• fixed GUI error saving FXS Clip
• fixed problem with dialplan restore
• debug files get tagged with their md5sum now
• improved DNS SRV handling
• improved SMS handling

16.05 - 27.01.2017

• fixed GUI error setting t38 in dialplan
• fixed GUI error saving GSM extension
• fixed GUI error setting call progress table
• fixed GUI Dialplan-Debug behaviour
• fixed one way audio problem on SIP→SIP calls
• fixed reinvite handling on SIP→SIP calls

16.04 - 22.12.2016

• fixed error storing "more settings" in dialplan
• fixed limitation on density of inbound SIP calls

16.03 - 29.11.2016

• new responsive GUI
• new logging facilities
• new config option skip_setup_ack
• new config option resync_on_notify
• new config option isdn_dad_setting
• new config option dialtone_digits
• added dialplan variable new_destination_auto
• fixed VLAN issues
• fixed problem with dialplan copy and multiple delete
• fixed SMS problems
• fixed problem with SIP info messaged on FXS calls
• try option 67 on DHCP if option 66 is missing
• display name in register requests now in quotes
• in-call ISDN Information messages will now converted to DTMF
• fixed some minor issues in the GUI
• fixed problem with provisioning polling
• fixed config option outgoing_bchannels
• new REST-API functions
• netconfigserver is now configurable
• improved qsig name handling
• support for DNS SRV
• minimum accepted session expires now configurable
• Major security fixes, more info here

Known Issues:

• T38 disable doesn't save in the Dialplan  - as workaround you can configure "t38=0" in the text-area under the "more" tab.

3.0 STABLE - Firmware

3.0.19 - 25.07.2017

• added option no100fix, fixing problem when no 100 trying is received
• fixed sip failover behaviour on gsm
• fixed memory leak when using stun
• fixed problem encoding ISDN connected party number

3.0.18 - 24.05.2017

• Security fix, telnet interface not more accessible from LAN by default
• fixed instablity problems in SIP stack occurring when a large time change shift happens

3.0.17 - 03.02.2017

• fixed problem in dialplan debug
• fixed problem with incoming 181 and 182 provisional responses
• fixed bug in Factory Reset

3.0.16 - 18.01.2017

• fixed return code for provisioning

3.0.15 - 12.01.2017

• reworked session handling for dialplan debug for more security

3.0.14 - 10.01.2017

• reworked GUI session handling. GUI is now more secure as its files can only be accessed via the GUI
• new_source_auto will now use TON_SUBSCRIBER as default

3.0.13 - 29.11.2016

• new config option skip_setup_ack
• new config option dialtone_digits for FXS inbound cals
• new config option emergency
• display name in register requests now in quotes
• in-call ISDN Information messages will now converted to DTMF
• fixed config option outgoing_bchannels
• bugfix gsm provisioning
• fixed problem with SIP info messaged on FXS calls
• fixed problem with SDP offers containing 16000Hz Codecs